What happens when you buy a netbook on auction for a friend, advertised as used in great condition with minimal wear and then the scammy seller sends you a machine that had it's hinge support posts broken off and what's worse: destroyed by a less than useful kludge? Well, if you're like me then after the negotiations have gone nowhere and the seller got the well deserved negative feedback (won't go there) you start thinking of ways to salvage the situation.
Here's the horror show:
You can't see it but basically someone tried soldering the metal threaded inserts into the plastic and once they were either satisfied with their "work" (the thing and beads of solder were rolling around inside the case when I got it..) or they realized the futility of their actions they then proceeded to drown everything in super-glue.
Turns out I should've done my research because the hinge supports were notoriously bad on this model and a large percentage of them that I've seen advertised since have had the same issue (minus the butchery of course)
The machine itself is some off-brand cheapy so got what I deserved and paid for, I guess..
The support posts were beyond hope so after racking my brain for a little while I came up with a following solution:
So now I could tighten the case together by using a nut where the screw went originally.
I also cleaned up the hinges (which were really seized up with grime and some leaked super glue) using dental floss and a tiny amount of mineral oil which worked really surprisingly well.
Did this quite a while ago and the machine (and hinges) have been in constant, daily use for the past 5 months at least. So far they're holding up great.
As an added bonus, the same person who botched up the case also turned out to have replaced the CMOS battery at some point by ripping the spot-welded tabs off the original and and loosely duct-taping them to a new one...
After all that the machine still has some sort of issue that I couldn't figure out but I'm sort of guessing that that's BGA-related so I'm not going to bother with it. It hard-locks under heavy load when cold booted (literally.. once it has warmed up the issue can't be reproduced. *shrug*)
Here's the horror show:
You can't see it but basically someone tried soldering the metal threaded inserts into the plastic and once they were either satisfied with their "work" (the thing and beads of solder were rolling around inside the case when I got it..) or they realized the futility of their actions they then proceeded to drown everything in super-glue.
Turns out I should've done my research because the hinge supports were notoriously bad on this model and a large percentage of them that I've seen advertised since have had the same issue (minus the butchery of course)
The machine itself is some off-brand cheapy so got what I deserved and paid for, I guess..
The support posts were beyond hope so after racking my brain for a little while I came up with a following solution:
- Cleaned up everything and filed off all the broken and melted parts until the stubs were level.
- Drilled and countersunk holes from the top of the case where the posts were (or at least that was the plan but plastic just grips and pulls the drill bit so they both went a bit too deep, eh..)
- Added long screws through the countersunk holes and spacers from a plastic tube on the inside (as a prosthetic to replace the broken sections of the support posts)
So now I could tighten the case together by using a nut where the screw went originally.
I also cleaned up the hinges (which were really seized up with grime and some leaked super glue) using dental floss and a tiny amount of mineral oil which worked really surprisingly well.
Did this quite a while ago and the machine (and hinges) have been in constant, daily use for the past 5 months at least. So far they're holding up great.
As an added bonus, the same person who botched up the case also turned out to have replaced the CMOS battery at some point by ripping the spot-welded tabs off the original and and loosely duct-taping them to a new one...
After all that the machine still has some sort of issue that I couldn't figure out but I'm sort of guessing that that's BGA-related so I'm not going to bother with it. It hard-locks under heavy load when cold booted (literally.. once it has warmed up the issue can't be reproduced. *shrug*)
